Monitor Tests Forum

Full Version: AMD/ATI Pixel Clock Patcher
You're currently viewing a stripped down version of our content. View the full version with proper formatting.
(01-08-2014 12:03 PM)Shogun Wrote: [ -> ]Hello Toasty, got a question for you in regard of an Active adapter

Goy myself a lappy Asus G75 VW that has a nvidia 670M, which has 1 hdmi, 1 vga and 1 mini DP.

I'd like to bring my lappy to a lan party ad use my Qnix 1440p at 120hz, so i went and did some research and bough this specific adapter.

http://www.ebay.com.au/itm/BIZLINK-DISPL...35cdc0d06b

It states that is a dual link D that will support resolution up to 1440p/2560*1600, however, im not sure about the refresh rate.

Do you know if it's possible get at least 110hz using that kind of adapter while using that adapter, connected to the Qnix monitor?
And if so, what is the procedure to get it done?
The only DisplayPort to dual-link DVI adapter I know about that can handle higher pixel clocks is this Accell adapter: https://www.amazon.com/dp/B00856WJH8/?tag=mtests-20#ad

It must be the one with 3D support (model B087B-007B), not the regular one. Even though it says 330 MHz pixel clock, supposedly it can handle around 400 MHz pixel clock. You might not be able to get 110 Hz, but 100 Hz should be possible.

Those adapters use DisplayPort, so the patch shouldn't be needed. You might run into problems adding custom resolutions if the laptop has switchable graphics. You'd have to add the custom resolution using Intel's control panel and not NVIDIA's, and I don't know what restrictions Intel has.
Hey Toasty, thank you for your continouos work on this patch.

I have just updated my graphics drivers from 13.9 to 13.12 and am experiencing problems, although I'm unable to completely pin down their origin.
With driver version 13.9 and a 1.1 version of your patch I was able to run my QNIX QX2710 on 2560x1440@120Hz just fine.
Now that I've updated to 13.12 and applied the most recent version of the patch, it reports that it patched all the limits, but I am still unable to select the custom resolutions I created with CRU.

I've already tried completely removing all AMD drivers from my PC, rebooting, then reinstalling them, then rebooting again before applying the patch, still, the result wasn't different.
I've also reset all EDID's using CRU, rebooted and then configured the monitor's again, still, in vain.
Even disabling avast! during patching, attempts to set the refresh rate using DisplayFusion and enabling/disabling testmode and rebooting did not help with this.

The Catalyst Control Center even reports the monitor at a max. resolution of 2560x1440@120Hz, but I just can't seem to apply it.

I have attached two screenshots showing the CCC, the patcher and CRU; I hope you can help me in some way.
Use the arrow buttons to order the refresh rates from highest to lowest, and remove all the non-2560x1440 resolutions because that monitor can't handle them. Enable GPU scaling if you want to use lower resolutions. The extension block should also be disabled because the monitor doesn't actually have one, but that shouldn't make a difference with AMD cards.
(01-12-2014 04:20 AM)ToastyX Wrote: [ -> ]Use the arrow buttons to order the refresh rates from highest to lowest[...]

Thank you very much, this method worked.
Now I'm only able to select 120Hz as the refresh rate, but that doesn't really bother me, as it is the only one I'd use anyway.

Although I am unable to activate GPU scaling in any way, I can select it and apply it, but it just reverts itself directly.
(01-12-2014 10:45 AM)CheddarCheese Wrote: [ -> ]Now I'm only able to select 120Hz as the refresh rate, but that doesn't really bother me, as it is the only one I'd use anyway.
That's really weird. Did you delete 1920x1080 @ 120.003 Hz? 2560x1440 @ 120 Hz needs to be listed first and not 1920x1080 @ 120.003 Hz.

You shouldn't need to add any lower resolutions. 1920x1080 and other standard resolutions should be available as scaled resolutions even if you don't add them.

AMD's driver is really weird about GPU scaling. You have to switch to a lower resolution to set it, and sometimes the setting won't stick with certain resolutions.
I'm posting to report something weird,
Just installed the 13.20 RC3 drivers, and the patcher shows this :
CRU is the same as before, but 120hz doesn't show up.

[Image: cnDbz2T.png]
I'm not familiar with that version. It looks like a non-standard release. The patcher needs to be updated to work with the new driver. Try this: https://www.monitortests.com/atikmdag-patcher-1.2.3.zip
Wow. That was quick to get a new version out. I just signed up here to say thanks. Works like a charm with 13.30. I am nowhere near technically inclined enough to be helpful. But I can show gratitude to those that are, and are willing to share.

Thanks Again.
-Kyle
thanks, will try myself,
it was a released beta driver. will be a WHQL for kavari (spelling)

new tool works perfectly, thanks again!
Please help, I used this patch a few weeks ago to overclock my Qnix with my AMD HD7850, recently I ordered a GTX780 to replace the 7850. While waiting for the new card I figured I'd practice wiping all AMD drivers to be ready for any problems when the new card arrived. I uninstalled catalyst, ran 'reset-all' with CRU, did what this site said to restore to unpatch, and then I went through and manually removed all traces of AMD drivers.

After I did the full AMD wipe I did a fresh AMD driver install without this patcher. After this when I try to benchmark or run a game it crashes and says something like 'your graphic driver stopped responding but has been fixed' other times it would lock up completely, and one time I had a BSOD.

I then did the full AMD wipe again and installed my GTX780 hoping that it being completely different drivers would fix the problem but it didn't. I'm still getting lock ups and crashes.

It's seems to me the patcher has changed something in the registry (regarding graphics) that I cannot repair.

Can someone please point me to all the files changed by the patcher so I can manually replace them and get my system working again (without patch)?

It would be greatly appreciated because my only other option is to format and start fresh with a clean OS install.
Reference URL's