Post Reply
Custom Resolution Utility (CRU)
03-13-2014, 06:36 AM
Post: #761
RE: Custom Resolution Utility (CRU)
update , got all 3 LG 42LN5400 working at 75hz , 1 on hdmi , 1 on mini displayport to hdmi active , 1 on dvi d via ati adapter to hdmi , got rfactor and ut2004 working , but they seen to lag or something ,just not as smooth as 60hz , would i be better off going to samsungs 40in 3d TVs ? they would be more cash ,but i got 10 days to return the LGs


steve
Find all posts by this user
Quote this message in a reply
03-14-2014, 04:04 AM
Post: #762
Thumbs Up RE: Custom Resolution Utility (CRU)
First i'll like to say, thanks so much for the tool! Smile.

The only problem i have is that the tool does not seem to recognize anything past 4095 Horizontal pixels.

I downsampled my 21:9 2560x1080p Dell Monitor to 5120x2160 30Hz for benchmarking purposes, but applications do not recognize the refresh rate, so i was trying to set it through CRU as usual, but it turns red whenever i input 5120 Sad

Could you increase the limit on the tool? Or is it something that can't be done. Either ways, thanks a lot
Find all posts by this user
Quote this message in a reply
03-14-2014, 05:01 AM
Post: #763
RE: Custom Resolution Utility (CRU)
(03-14-2014 04:04 AM)yungbenny911 Wrote:  First i'll like to say, thanks so much for the tool! Smile.

The only problem i have is that the tool does not seem to recognize anything past 4095 Horizontal pixels.

I downsampled my 21:9 2560x1080p Dell Monitor to 5120x2160 30Hz for benchmarking purposes, but applications do not recognize the refresh rate, so i was trying to set it through CRU as usual, but it turns red whenever i input 5120 Sad

Could you increase the limit on the tool? Or is it something that can't be done. Either ways, thanks a lot
That's an EDID limitation. There's no way to define 5120x2160 with an EDID override.
Find all posts by this user
Quote this message in a reply
03-14-2014, 05:04 AM
Post: #764
RE: Custom Resolution Utility (CRU)
(03-13-2014 12:26 AM)dice65 Wrote:  hi guys, i have gotten my 42in LG hdtvs to 75hz so far at 1920x1080 , i have 2 6970s with 2 cross bridges , why would a game {rfactor] studder at that rez at 75hz ?
Either the TV is skipping frames or the game is limited to 60 fps.

Use this test with a camera to check if the TV is skipping frames: http://www.testufo.com/#test=frameskipping
Find all posts by this user
Quote this message in a reply
03-14-2014, 05:05 AM
Post: #765
RE: Custom Resolution Utility (CRU)
(03-12-2014 10:36 PM)mdrejhon Wrote:  Does Intel graphics support DDC/CI?
Yes, but it requires their API, which isn't publicly available.
Find all posts by this user
Quote this message in a reply
03-14-2014, 07:40 AM
Post: #766
RE: Custom Resolution Utility (CRU)
thanks toasty !! , i returned the LGs an picked up 3 samsung un40fh6030f sets , i love em lol , much better an smoother pic than the lgs , still cant seem to figure out what im doing wrong or not doing right , cant get 1 of em to get above 60hz, got them setup in eyefinity right now , iracing never looked so good even at 60hz , lets get these babys rolling lol, thanks for your help !! i uploaded a edid over at 3dvision blog , maybe that will work ,ill keep you updated


steve
Find all posts by this user
Quote this message in a reply
03-14-2014, 10:54 AM (Last edited: 03-14-2014, 11:41 AM by pindu)
Post: #767
RE: Custom Resolution Utility (CRU)
hello
need help please

trying to change res on eizo rx240 from native max of 1200x1600 to higher

quadro4000m connected via dp.

when i run cru i get this messagr "access violation at ......"
when i cancel this box cru seems to work fine but res doesnt change

thanks

edit

ok got cru working but when i apply new res screen goes blank "signal error"
Find all posts by this user
Quote this message in a reply
03-15-2014, 07:58 AM
Post: #768
RE: Custom Resolution Utility (CRU)
(03-14-2014 10:54 AM)pindu Wrote:  when i run cru i get this messagr "access violation at ......"
This is unusual. Nobody else has ever reported this happening. This could be caused by an antivirus program doing something weird, or it could be a CRU bug. This would be hard to debug without seeing it happen myself.

(03-14-2014 10:54 AM)pindu Wrote:  ok got cru working but when i apply new res screen goes blank "signal error"
Higher resolutions will only work if the monitor can handle them.
Find all posts by this user
Quote this message in a reply
03-15-2014, 06:40 PM (Last edited: 03-15-2014, 06:43 PM by pindu)
Post: #769
RE: Custom Resolution Utility (CRU)
ok thanks

so is thelimiting factior the panel or monitor softwsare?
Find all posts by this user
Quote this message in a reply
03-15-2014, 10:21 PM
Post: #770
RE: Custom Resolution Utility (CRU)
(03-15-2014 06:40 PM)pindu Wrote:  so is thelimiting factior the panel or monitor softwsare?
The panel can only display the native resolution. Other resolutions would have to be scaled, and it's up to the monitor whether or not it can scale down higher resolutions.

It's possible to do scaling on the GPU, but not with CRU. CRU only deals with monitor resolutions. Since you have an NVIDIA GPU, you can use this process: http://www.neogaf.com/forum/showthread.php?t=509076
Find all posts by this user
Quote this message in a reply
 Post Reply


Forum Jump:


User(s) browsing this thread: 140 Guest(s)